Load Ratings |
|
Switch Channels |
6 |
|
Per Channel |
16 Amps at 100-277 Volts AC, 50/60 Hz |
|
Dim Load Types |
Incandescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, 2-wire fluorescent ballast, 3-wire fluorescent ballast, LED driver |
|
Switch Load Types |
Incandescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, fluorescent ballast, high-intensity discharge, LED driver |
|
Minimum Load |
15 Watts at 120 Volts;
25 Watts at 230 Volts;
30 Watts at 277 Volts |
Electrical Current Rise Times |
|
10-90% Rise Time |
300 µs with 8A load; 525 µs with 16A load |
|
0-100% Rise Time |
575 µs with 8A load; 900 µs with 16A load |
|
Maximum Rate of Current Change (di/dt) |
85 mA/µs |
Power Requirements |
|
Primary |
100-277 Volts AC, 50/60Hz, supplied via channel 1 (L1, N) |
|
Secondary (Optional) |
9 Watts at 24 Volts DC, supplied via Cresnet® |
Connectors |
|
NET |
(2) 5-pin headers, connects via included interconnect cable to adjacent module or internal connecting block |
|
N |
(1) Terminal block, line input neutral |
|
L1-L6 |
(6) Terminal blocks,[1] line power inputs |
|
SW1-SW6 |
(6) Terminal blocks, switch channel outputs;
For 3-wire loads only |
|
DM1-DM6 |
(6) Terminal blocks, dim channel outputs;
To be used for all 2-wire load types |
Controls & Indicators |
|
NET ID |
(2) 7-segment green LED digits and (2) miniature pushbuttons, sets Cresnet ID |
|
SETUP |
(1) Red LED and (1) recessed miniature pushbutton, enables setup mode and touch-settable ID |
|
OVR |
(1) Red LED and (1) miniature pushbutton, enables override mode and saves override presets |
|
PWR |
(1) Green LED, indicates power status;
Solid illumination indicates line power is applied to N and L1;
Flashing indicates Cresnet power is supplied in absence of line power |
|
NET |
(1) Yellow LED, indicates communication with control processor |
|
RESET |
(1) Recessed miniature pushbutton, resets internal processor |
|
Channel Section |
|
ON/DIM |
(2) Red LEDs per each channel, "ON" indicates channel is at a non-zero level, "DIM" indicates channel is at a non-zero level below 100% |
|
UP/DN |
(12) Miniature pushbuttons, manually activates individual channels and dims |
|
DIM/NON-DIM |
(6) Recessed miniature switches, sets channel mode;
When set to "NON-DIM" module will ignore dim commands |
Enclosure |
|
Surface mount module with (2) integral mounting flanges; mounts in a GLE enclosure |
Environmental |
|
Temperature |
32° to 104° F (0° to 40° C) |
|
Humidity |
10% to 90% RH (non-condensing) |
|
Heat Dissipation |
550 BTU/Hr |
Dimensions |
|
Height |
14.50 in (368 mm) |
|
Width |
6.00 in (152 mm) |
|
Depth |
7.10 in (180 mm) |
Electrical Regulatory Certifications |
|
UL508, Section 41 (Endurance Test) and Section 61C (Electronic Ballasts) |
|
UL924, Emergency Power Equipment |
|
IEC60669-2-1, Section 19.102 (Contact mechanisms incorporated in electronic switches, intended for fluorescent lamp circuits or other capacitive loads) |
|
SCCR Rating - 65kA |
|
CE |
|
CEC Title 24 2013 Compliant |