One-Touch Cable Retractor for FT2 ELEC Series, HD15 male to HD15 male, VGA, 1080p
Provides a retractable cable management solution for Crestron® FT2 ELEC Series FlipTops™ cable management system. Features an electrically clutched, spring powered retraction mechanism, which allows each cable to pull out smoothly and then retract with the touch of a button. Ideal for applications with limited space beneath the table.
Configure your FlipTop now!
Launch Configurator
Crestron® One-Touch Cable Retractors (FT2A-CBLR-1T Series) offer a refined cable management solution for use with Crestron FT2 ELEC FlipTop Series. Each cable pulls out smoothly up to 5 ft (1.5 m), and retracts gently back into the FlipTop™ with the touch of a button. The button on each module is backlit for visibility in a darkened room and is labeled with an international symbol icon indicating the connection type.
Automate one-touch retractors by connecting the retractors in a FlipTop to a control system and a switch or to a DMPS via a single Cresnet cable. Custom programming can trigger all the cables to retract after five minutes of no video being detected.
The retractor mechanism allows for a compact design that is ideal for applications where vertical clearance is limited beneath the table.
Each One-Touch Cable Retractor is composed of a retractor enclosure and pass-through module. The enclosure attaches to the FlipTop chassis beneath the table, while the module installs in the top of the FlipTop. A cable tail is provided below the table for connection to a DM® transmitter or similar interface device.1
The pass-through module occupies two module slots within the FlipTop. The retractor enclosure slides onto the side of the FlipTop chassis beneath the table and locks into place with a snap. Retractors normally install at the left and right ends of a module row but may also be installed in the middle of a row by adding an FT2A-CBLR-BRKT series mid-row adapter bracket (one per row, each sold separately).
The following one-touch, retractable HDMI® cable is offered:
FT2A‑CBLR‑1T-HD: 10.2 Gbps HDMI cable with a male HDMI Type A connector at both ends.
The following 4K compatible cables offered feature a minimum TMDS bandwidth of 18 Gbps to support ultra high-definition digital video signals up to 4K60 4:4:4. Active circuitry is employed for optimal performance.
- FT2A‑CBLR‑1T‑4K‑DP: DisplayPort™ cable with a male DisplayPort connector at both ends.
- FT2A‑CBLR‑1T‑4K‑DP‑HD: Cable with a male DisplayPort connector at the source end above the table and a male HDMI Type A connector at the sink end below the table; converts DisplayPort to HDMI to allow connection of a DisplayPort source to an HDMI input.1
- FT2A‑CBLR‑1T‑4K‑MDP‑DP: Cable with a male Mini DisplayPort connector at the source end above the table and a regular-sized male DisplayPort connector at the sink end below the table; converts Mini DisplayPort to standard DisplayPort to allow connection of a Mini DisplayPort source to a DisplayPort input.
- FT2A‑CBLR‑1T‑4K‑MDP‑HD: Cable with a male Mini DisplayPort connector at the source end above the table and a male HDMI Type A connector at the sink end below the table; converts Mini DisplayPort to HDMI to allow connection of a Mini DisplayPort source to an HDMI input.1
- FT2A‑CBLR‑1T‑4K‑USBC‑HD: Cable with a male USB Type-C® connector at the source end above the table and a male HDMI Type A connector at the sink end below the table; converts USB-C to HDMI to allow connection of a USB-C source to an HDMI input.1
A USB-C power module is available to support charging devices:
FT2A-CBLR-1T-USBC-PWR: USB Type-C cable with a male connector at the source end above the table and a male USB Type-C connector at the sink end that connects to a third-party USB power supply. Supports up to 60 W of power for charging devices only (does not transfer video or data).
NOTE: Crestron does not offer a USB power supply. A third-party power supply must be used with the device.
Additional models are available to support analog and data signals. These cable retractors are passive.
- FT2A‑CBLR‑1T‑VGA: VGA cable with a male HD15 connector at both ends; supports resolutions up to Full HD 1080p.
- FT2A‑CBLR‑1T‑AUDIO: Unbalanced stereo audio cable with a male 3.5 mm mini-TRS connector at both ends.
- FT2A‑CBLR‑1T‑CAT6: CAT6 LAN cable with a male RJ‑45 connector at both ends.
- FT2A‑CBLR‑1T‑USB: USB 2.0 cable USB Type-A male to USB Type-B male under the table to support connection to a codec or extender.
NOTE: FT2A‑CBLR‑1T series retractors are only compatible with FT2 ELEC series FlipTops. They are not compatible with FT2 MECH series FlipTops. See also the FT2A‑CBLR‑GR Series Gravity Cable Retractors for a lower cost alternative.
Key Features
- Connectivity for FT2 ELEC Series FlipTop cable management systems
- Electrically clutched, spring powered retraction mechanism
- Cable pulls out smoothly up to 5 ft (1.5 m) and retracts gently with the press of a button
- Control system integration enables remote retraction control
- Flexible, low friction flat cable construction
- Soft-feel sculpted connectors for easy handling
- Backlit international symbol icon identifies the connector type
- Active models support 4K60 4:4:4 digital AV signals
- Support for HDR and HDCP 2.2
- 4K models available to convert from DisplayPort™ to HDMI® connectivity, Mini DisplayPort to DisplayPort, Mini DisplayPort to HDMI, and USB-C® to HDMI connectivity
- Power module supports up to 60 W of power for USB-C® charging
- Passive models available for HDMI, VGA, stereo audio, LAN, and USB 2.0
- Requires two module slots at either end of a FlipTop™ module row
- Optional mid-row installation using additional brackets
- Retractor housing snaps onto the side of the FlipTop chassis beneath the table
- Requires only 11-5/8 in. (295 mm) vertical clearance below the table top surface
- Provides a 2.75 or 4.75 ft (0.8 or 1.4 m) long tail below the table1
| Cable |
| Pull-Out Length |
Up to 5 ft (1.5 m) above table |
| Back End Tail Length |
4.75 ft (1.4 m) beneath table except for models FT2A‑CBLR‑1T‑4K‑DP‑HD, FT2A‑CBLR‑1T‑4K‑MDP‑HD, FT2A‑CBLR‑1T‑4K‑USBC‑HD, and FT2A‑CBLR‑1T‑USBC‑PWR, which are 2.75 ft (0.8 m) |
| Button & Indicator |
| Retract |
(1) Pushbutton with blue LED backlit symbol icon indicating the cable connector type, button actuates retraction, LED illuminates constantly or flashes if cable cannot be retracted due to interfering tension or obstruction |
| Communications |
| Cresnet® |
Allows connection to a control system via the Cresnet port on the FlipTop, supports remote actuation of the retraction function |
| Environmental |
| Temperature |
32° to 113° F (0° to 45° C) |
| Humidity |
10% to 90% RH (non-condensing) |
| Construction |
| Pass-Through Module |
Precision fit plastic drop-in module, 2-slot, black |
| Retractor Enclosure |
Plastic, black |
| End-Row Mounting |
• Module requires two consecutive module slots at the left or right end of any module row within the FlipTop chassis;
• Enclosure attaches beneath the table to mounting slots on the left or right side of the FlipTop chassis;
• Requires 11.6 in. (295 mm) minimum vertical clearance beneath the top surface of the table;
• Projects 8.4 in. (213 mm) from the side of the FlipTop chassis beneath the table, and requires an additional 0.2 in. (5 mm) for installation |
| Mid-Row Mounting |
• Requires an FT2A-CBLR-BRKT series mid-row adapter bracket (one per row, each sold separately);
• Module requires two consecutive module spaces in the middle of any module row within the FlipTop chassis (refer to the relevant FT2A-CBLR-BRKT model spec sheet for additional details);
• Enclosure attaches beneath the table to mounting slots on the front or rear of the FlipTop chassis (via the bracket);
• Requires 11.6 in. (295 mm) minimum vertical clearance beneath the top surface of the table;
• Projects 8.8 in. (223 mm) from the front or rear of the FlipTop chassis beneath the table, and requires an additional 0.2 in. (5 mm) for installation |
| Dimensions |
| Height |
8.95 in. (228 mm) |
| Width |
10.30 in. (262 mm) |
| Depth |
2.24 in. (57 mm) |
| The dimensions shown are for the retractor enclosure only. |
| Compliance |
| CE |
Click
here to search product certificates.
Please select your region below to see the appropriate Advertised Pricing.